Injection Molding Essays (944 words) - Injection Molding

Injection Molding Injection Molding Injection molding is a process used to form products from plastic. The process requires a mold, clamping component, injection unit, and some sort of plastic. As time has advanced so has injection molding by developing new techniques and new products to aid in the manufacturing of the injection molded parts. Injection molding was used as early as the 1860's. It can be used to form many different products. Whether the products are small, large, complex, or simple they can be produced. Injection molding has derived from metal die casting. However, the polymer can't just be poured into a mold, it has to be forced into the mold cavity. The polymer is forced into the mold and pressure is held on it to avoid shrinkage in the mold cavity as it cools. Injection molding is capable of producing a large number of parts with very high precision. All thermoplastics except polytetraflouroethylene (PTFE), polyamides, and some aromatic polyesters can be used by the injection molding machine. Some thermosetting plastics can also be used. The typical fabrication process can be done by one of two different types of injection molding equipment. Either a plunger, or reciprocating screw type machine can be used. The process starts by melting the polymer resin. Once the resin is melted, a mold is placed in the clamping unit. The clamping unit is to hold the mold together. The plunger or reciprocating screw then force the polymer resin into the mold. In the plunger operated machine, the plunger is hydraulically operated. This forces the plastic through a heated area, where it is then spread into a thin layer by the torpedo. Then the melt comes to the nozzle and is injected into the mold. The reciprocating screw rotates, this moves the polymer resin forward for injection. As the screw rotates it acts to melt, mix, and pump the polymer to prepare it for injection. The reciprocating screw machine is the most widely used of the two machines. Once the polymer resin is injected into the mold cavity, the mold is allowed to cool. The mold has a gate, which limits back flow and directs the flow of the melt into the mold cavity. Once the mold has cooled and the polymer has solidified the mold can be removed and the part can be ejected. When the gate freezes, the screw begins to rotate again and the part is ejected. This completes the cycle time. Cycle times range due to the amount of time the polymer needs to cure or solidify. This is called the hold time. Some advantages of injection molding are high production rates, design flexibility, low tolerances, can process wide range of materials, low labor, little or no finishing, and scrap is held to a minimum. However, some disadvantages are high startup and running costs, part must be designed for effective molding, accurate cost prediction is difficult, and machine cost is very high. The high tooling costs come from the molds being built to a high level of precision. The molds are usually constructed of hardened tool steel, and aluminum or other soft metals when tooling life is not an issue. Tooling costs can range from $5,000 to $100,000. However, there are some parts that can not be formed by any other method of processing except injection molding. These parts typically become feasible around 1,000 pieces. To go with the high tooling costs there are a large number of variables that go along with it. Injection molding machines may require special plant services that other equipment does not. As technology advances so must the industry to keep up production. One way injection molding is keeping up is by becoming automated. Usually, operators are placing parts into molds, and then taking the parts out. Now, robotic devices are being used to place inserts before molding and remove parts after molding as well as a host of other operations as well. Not only does the robotics speed up the process, but makes it much more cost effective. Another way industry is trying to keep up with technology is by using computer software. The software is called ?Mold Adviser,? which is a mold design and analysis package that can be used to help speed up operations while reducing tooling costs. Using the past standard operation of designing molds a company could easily waste six to twelve weeks and anywhere from $30,000 to $40,000 on fixing a mold that has a problem with filling correctly. The new software